Shanghai Shengliang Electronic Technology Co., Ltd.
When using a loader scale, it's essential to follow proper procedures to ensure accurate measurements and extend the equipment’s lifespan. Shanghai Shengliang Electronic Technology Co., Ltd. has compiled five key tips to help users get the most out of their JM-T7000 loader scale. Choosing quality means choosing reliability.
First, before starting the JM-T7000 loader scale, it's recommended to start the loader first and lift the boom 5–10 times for preheating. This helps warm up the hydraulic oil and pressure sensors to their optimal working temperature, reducing the impact of temperature fluctuations on measurement accuracy.
Second, during the weighing process, avoid moving the loader while it is being weighed. Once the weighing is complete, you can adjust the speed as needed. However, if you must move while weighing, keep the speed below 5 km/h, as this may reduce accuracy by approximately 0.5%.
Third, when lifting the boom using the position sensor, maintain a steady and consistent speed. Avoid sudden acceleration, deceleration, or stopping, as these actions can affect the stability of the measurement.
Fourth, for best results, weigh the loader on flat ground or on slopes that are less than 15 degrees. Uneven terrain can introduce errors and compromise the reliability of the readings.
Lastly, after completing a single weighing, lower the loader’s bucket to its lowest position before the next use. This ensures the JM-T7000 loader scale is ready for the next operation and helps maintain system performance over time.
By following these simple yet effective guidelines, users can maximize the efficiency and accuracy of their loader scale, ensuring long-term value and reliable performance. Always refer to the manufacturer's instructions for detailed guidance and support.
When using a loader scale, it's essential to follow proper procedures to ensure accurate measurements and extend the equipment’s lifespan. Shanghai Shengliang Electronic Technology Co., Ltd. has compiled five key tips to help users get the most out of their JM-T7000 loader scale. Choosing quality means choosing reliability.
First, before starting the JM-T7000 loader scale, it's recommended to start the loader first and lift the boom 5–10 times for preheating. This helps warm up the hydraulic oil and pressure sensors to their optimal working temperature, reducing the impact of temperature fluctuations on measurement accuracy.
Second, during the weighing process, avoid moving the loader while it is being weighed. Once the weighing is complete, you can adjust the speed as needed. However, if you must move while weighing, keep the speed below 5 km/h, as this may reduce accuracy by approximately 0.5%.
Third, when lifting the boom using the position sensor, maintain a steady and consistent speed. Avoid sudden acceleration, deceleration, or stopping, as these actions can affect the stability of the measurement.
Fourth, for best results, weigh the loader on flat ground or on slopes that are less than 15 degrees. Uneven terrain can introduce errors and compromise the reliability of the readings.
Lastly, after completing a single weighing, lower the loader’s bucket to its lowest position before the next use. This ensures the JM-T7000 loader scale is ready for the next operation and helps maintain system performance over time.
By following these simple yet effective guidelines, users can maximize the efficiency and accuracy of their loader scale, ensuring long-term value and reliable performance. Always refer to the manufacturer's instructions for detailed guidance and support.
SMIRO sliding doors have many advantages:The wall thickness of the door is 3.0, the glass is not paintedand the production is easier;Micro-edge micro-slit design, the visual surface is only 5 mmthere is almost no gap between the door and the track;No grip with damping buffer, no ground rail design,transparent and bright,good health management;Standard 8mm tempered glass, inner rubber process slidingdoor.
The service life of aluminum sliding windows is affected by many factors:
1. Material quality
Aluminum alloy profiles
If high-quality aluminum alloy profiles are used, the wall thickness meets the standard and the alloy composition is excellent, its service life can reach 30-50 years or even longer. For example, some high-quality aluminum alloy profiles such as 6063-T5 have strong corrosion resistance and deformation resistance.
Hardware accessories
Hardware accessories such as pulleys, handles, locks, etc. have a greater impact on the overall life. Good quality stainless steel or copper hardware accessories can be used for 10-20 years under normal use. Cheap and low-quality hardware may be damaged in 5-10 years, such as pulley wear leading to poor sliding and pulling.
2. Use environment
Climatic conditions
In dry and mild climates, aluminum sliding windows have a longer service life. However, if they are located in coastal areas, high humidity and high salt air will accelerate the corrosion of aluminum alloys, which may shorten the service life to about 20-30 years; in areas with more acid rain, it will also cause erosion on its surface.
Daily maintenance
Regular cleaning, maintenance, and timely replacement of aging parts of aluminum sliding windows will greatly extend their service life. On the contrary, if there is a long-term lack of maintenance, the life of the window may be reduced by 5-10 years.
sliding door bathroom,sliding glass door replacement cost,installing sliding glass door
SMIRO DOORS AND WINDOWS CO., LTD , https://www.smirowindows.com