(1) Take out the pipe plug of the ground drain, and check that there is no debris in the pipe, then clean the pipe around.
(2) Align the toilet outlet pipe with the water outlet, level it, and draw a mark on the hole of the toilet bolt, and remove the toilet.
(3) Insert a hole with a diameter of 20 mm and a depth of 60 mm at the mark, insert a 10 mm diameter bolt into the hole, secure it with cement, place the toilet eye on the bolt, and make it match the mark. After the test, The toilet is removed. Put the putty around the toilet outlet and the lower water outlet, and then align the four bolt holes of the toilet with the bolts, level them, put the rubber pads on the bolts, screw the nuts, and tighten them to a tight degree.
(4) Align the center of the rear end of the toilet, draw a vertical line, draw a horizontal line at a height of 800 mm from the ground, draw a mark on the horizontal line according to the position of the two side holes on the back of the tank, and make a diameter of 30 mm and deep at the hole. 70 mm hole. Insert a bolt with a diameter of 10 mm and a length of 100 mm into the hole and secure it with cement. Hang the back water tank on the bolt and lay it flat. In particular, align it with the center of the toilet bowl. Place the rubber pad on the bolt and screw the nut to the tightness.
(5) When installing the water tank elbow, first remove the nut of the back water tank and the water inlet of the toilet, and put it back to back on the water elbow, and the rubber mat is also placed on the water pipe. Insert the upper end of the sewer elbow into the drain of the back tank, insert the lower end into the water inlet of the toilet bowl, then push the rubber pad to the nozzle, screw the nut, straighten the water elbow, and tighten it with pliers. Moderate.
(6) When connecting the water with the eight-character door, first measure the size of the water tank opening of the water tank drifting door, match the short section, install the eight-character door, and put it into the upper water pipe. Broken the copper tube or plastic tube, bend the mother's lamp fork, and then put the drift door and the splayed door nut back to the copper tube or plastic tube. The two ends of the tube are wrapped with oil asbestos rope or lead oil and twine, respectively. Inside the door and the entrance of the eight-shaped door, tighten the nut.
Penetrating seal Curing Agent
What is the infiltration of sealing and curing materials?
Infiltration-type sealing and curing materials (commonly known as concrete sealing hardener or chemical dust-hardener penetrant) is a new generation of lithium-ion water-based products composed of inorganic substances, chemically active substances and silicon compounds. The product is a colorless transparent liquid material, easy to use, colorless, odorless, non-toxic, non-flammable, strong penetration, can be permanently sealed concrete, VOC-free ingredients, USDA USDA test. The product, through effective penetration, undergoes complex chemical reactions with free calcium oxide components in concrete. In the three-dimensional space to form a network structure, resulting in hard material, making the concrete structure is more compact, strong, effective sealing of the pores, will never prevent concrete dust from surface porosity in the precipitation. This results in a dust-free, compact, high-strength, highly abrasion-resistant, marble-lined concrete floor. Greatly improve the impermeability of concrete, wear-resistant, freeze-thaw cycles, hardness and other performance indicators, the longer the longer the gloss the better.
Scope of application:
Permeability seal curing materials (concrete strength of C20 above the ground design requirements): the need to clean the environment, the amount of dust in the air have certain requirements, but not suitable for the surface coating material area. Applicable to any indoor and outdoor hard, highly abrasion, impermeability of the plane demanding the old and new concrete, terrazzo, cement-based wear-resistant floor and cement mortar surface, such as cement-based building materials such as factories, shopping malls, Warehouses, parking lots, service stations, hangars, freight distribution centers, roads and other areas.
Use maintenance:
1, the construction of the floor just recommended in the first 1-3 months often with acidic detergent or water to clean the ground, because often water cleaning will speed up the reaction process, making the ground seal curing effect completed in advance, the gloss will appear earlier .
2, try to avoid alkaline cleaning agents and other substances in the floor surface stay.
3, if oil, color liquid, etc. should be promptly erased, otherwise it may leave a mark on the surface.
Precautions:
1, the infiltration of sealing and curing material itself does not change the smoothness and flatness of the base surface, the old ground and low intensity whether the ground appears to be dependent on the original ground conditions may be, but the ground strength, hardness, wear resistance, gloss Such instructions will be significantly improved.
2, mechanical calendering ground, terrazzo ground and wear-resistant ground after the use of polishing will immediately appear luster, the longer the use, the better the sense of the effect.
3, low strength, dust, rough surface of the ground (wear-resistant surface floor, terrazzo floor, concrete floor), the amount of standard materials can not play a role, need to increase the amount and increase the process; but the ground conditions are extremely poor, loose structure Under the situation (turning the cement mortar floor), increase the amount may not play a corresponding role.
4, the mirror effect Floor is the highest standard floor, the original surface to be the standard requirements of the ground, a large amount of material and ultra-fine polishing process.
5, This product is non-toxic, tasteless. For non-combustible products, it should be stored in a cool and dry environment.
6, This product can only be used plastic containers, can not be used metal containers and can not touch metal objects.
7, construction curing period of 7 days, can be used during conservation period, but need to pay attention to prevent heavy impact, scratches and so on.
8, this product may not be diluted, and to prevent freezing.
9, infiltration seal curing material can be used without freezing, but the strength of the growth time should be extended; infiltration seal curing material should be used when the floor temperature is greater than 5 ℃.
10, infiltration seal curing materials, such as accidentally splashed into the eyes, apply a lot of water rinse. Store in a place not accessible to children, swallowed.
Sealed Curing Agent,Concrete Seal Curing Agent,Concrete Sealing Curing Agent,Concrete Curing Agent
Jiangmen Kasole Building Materials Co., LTD. , http://www.kasole-paint.com