How to install the toilet? The toilet bowl is an indispensable bathroom product for every household. However, many people choose to buy the toilet after they buy it, but many people do not really understand this installation technique. Bring a lot of trouble to your daily life. Therefore, at the request of all the small partners, Xiao Bian will tell you today about how to install and install the toilet.
First of all, remember to first conduct a comprehensive inspection of the sewage pipeline to see if there is any blockage in the pipeline, such as sediment, waste paper, etc., and also check whether the floor of the toilet is installed horizontally before and after, if the ground is found to be uneven, Be sure to level the floor first when installing the toilet. Then the water outlet saw is short, and the most important point is that before installing the toilet, small partners must first determine whether the product, accessories, and instructions you selected are complete. You can first look carefully at the manual and learn about some products. Matters before you start the installation.
Secondly, at the beginning of the installation, the water outlet of the toilet should be aligned with the mouth of the water pipe. After laying flat and placing it right, draw a mark on the bolt holes of the toilet bowl, then remove the toilet and start marking. The holes are usually drilled with holes of 20 mm in diameter and 60 mm in depth. After the holes are drilled, 10 mm diameter bolts are inserted into the holes and cement is used to secure the holes. Then the eyes of the toilet are aligned with the bolts. Put the putty around the water outlet of the toilet bowl and around the mouth of the sewage pipe. After aligning the four bolt holes of the toilet seat, put on the rubber pad.
Finally, when installing the backwater tank water elbow, first remove the nuts of the backwater tank water outlet and the toilet water inlet, and then put them back to back on the water elbow, and the rubber pads are also placed on the sewage pipe, and then Insert the upper end of the water elbow into the drain of the back tank, insert the lower end into the water inlet of the toilet, then push the pad to the nozzle, screw on the nut, and find the position of the elbow, and then use Tighten the pliers on the line. However, it is also necessary for small partners to remember that when connecting water with the eight-character door, it is necessary to measure the size of the water tank sluice gate from the mouth of the water inlet, and then allocate a short section, install the eight-character door, and put it into the mouth of the upper water pipe.
How to install the toilet? I believe that the small partners have read the above description of the Xiaobian has been understood, but Xiaobian still suggested that everyone as much as possible please ask a professional installer to install, this will not only save time and effort, but also You can save a lot of unnecessary trouble.
First of all, remember to first conduct a comprehensive inspection of the sewage pipeline to see if there is any blockage in the pipeline, such as sediment, waste paper, etc., and also check whether the floor of the toilet is installed horizontally before and after, if the ground is found to be uneven, Be sure to level the floor first when installing the toilet. Then the water outlet saw is short, and the most important point is that before installing the toilet, small partners must first determine whether the product, accessories, and instructions you selected are complete. You can first look carefully at the manual and learn about some products. Matters before you start the installation.
Secondly, at the beginning of the installation, the water outlet of the toilet should be aligned with the mouth of the water pipe. After laying flat and placing it right, draw a mark on the bolt holes of the toilet bowl, then remove the toilet and start marking. The holes are usually drilled with holes of 20 mm in diameter and 60 mm in depth. After the holes are drilled, 10 mm diameter bolts are inserted into the holes and cement is used to secure the holes. Then the eyes of the toilet are aligned with the bolts. Put the putty around the water outlet of the toilet bowl and around the mouth of the sewage pipe. After aligning the four bolt holes of the toilet seat, put on the rubber pad.
Finally, when installing the backwater tank water elbow, first remove the nuts of the backwater tank water outlet and the toilet water inlet, and then put them back to back on the water elbow, and the rubber pads are also placed on the sewage pipe, and then Insert the upper end of the water elbow into the drain of the back tank, insert the lower end into the water inlet of the toilet, then push the pad to the nozzle, screw on the nut, and find the position of the elbow, and then use Tighten the pliers on the line. However, it is also necessary for small partners to remember that when connecting water with the eight-character door, it is necessary to measure the size of the water tank sluice gate from the mouth of the water inlet, and then allocate a short section, install the eight-character door, and put it into the mouth of the upper water pipe.
How to install the toilet? I believe that the small partners have read the above description of the Xiaobian has been understood, but Xiaobian still suggested that everyone as much as possible please ask a professional installer to install, this will not only save time and effort, but also You can save a lot of unnecessary trouble.
Toilet toilet blocked how to do children's toilet toilet toilet baby toilet toilet child toilet toilet toilet toilet for children
Copper Panels,Copper Composite Panel,Fr B1 Acp,Fire Resistance Acp
zhejiang kangzhan new materials co.,ltd , https://www.mcbondacp.com